JUST HOW TO INSTALL A BATHTUB: SET UP AN ACRYLIC TUB AND BATHTUB SURROUND

Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround

Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround

Blog Article

Try Here

Everybody is bound to have their own individual opinion involving Installing A Bathtub.


A Step-by-Step Guide to Installing a Bathtub
Setting up a tub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and also often, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old bathtub is easily easily accessible, the task can move rapidly; if you need to open up a wall to remove the old tub and position the brand-new tub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly require an assistant to move out the old bathtub and set in the new one. Make sure you have qualified yourself for the job and also fit attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is better to take into consideration using one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This post will help you mount a brand-new tub in your bathroom if you have currently gotten a new bathtub and do not need to alter the arrangement of your previous water pipes.
Your devices and product checklist must make up the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Planning for the Setup


    Firstly, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
    Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you make use of all of the provided washers.
    Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final setting.

    Removing Old Touches


    If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited accessibility that is often the case.
    Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
    Before moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Setting up the Tub


    Using both wood boards under its feet, put the bath tub in the required position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny points.
    The following goal is to guarantee that the tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub until the level checks out level.
    To mount faucets, fit the bottom of the furthest adaptable tap adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
    Activate the water as well as inspect all joints as well as brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as also examine the overflow electrical outlet and the regular outlet for leaks.
    Lastly, repair the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the bath tub ought to wait until the bath tub has been used at the very least when as this will settle it right into its final placement.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipes.
    If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, causing the water to permeate the wall surface between the bathroom and also the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
    You can choose from a range of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to permit the movement experienced when the tub is in use. The sealant can split rather very early if you do not think about this activity prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or water resistant sticky and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I came across that page on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the internet. Do you know about another individual who is in the market for the niche? Be sure promote it. We value reading our article about How to Install a Bathtub Yourself.




    Click On This Link


    Report this page